# Runs perfectly using Python 2.7.3 on Raspian. # GPSD Official Documentation: # http://www.catb.org/gpsd/gpsd_json.html # Original GpsPoller script by Dan Mandle: # http://www.danmandle.com/blog/getting-gpsd-to-work-with-python/
Last night I decided to customize my Logitech G19s keyboard screen to look like either a PipBoy or RobCo terminal interface.
Downloaded LCDHost in order to customize the look.
See the PipBoy Layout here.
What follows is the progression of getting the screen to look and “feel” right.
I’ve had an Intel motherboard and a Core 2 Duo sitting around for a while, and recently upgraded the graphics card in my main computer from a GTX 670 2GB to a GTX 770 4GB, so I decided I would build a portable gaming computer, as my main system weighs in at around 45 pounds and is not the easiest to transport.
Case: Cooler Master HAF XB Evo
Motherboard: Intel DG35EC – microATX
PSU: Corsair CX600 600W
RAM: 4GB Crucial PC2-6400
CPU: Intel Core 2 Duo E8300 – 2.83GHz
CPU Cooler: ARCTIC Freezer 11LP
GPU: EVGA GTX 670 2GB GDDR5
The motherboard does not natively support USB 3.0, so I also ordered a USB 3.0 host card with 20-pin internal connector.
I might add the anti-dust AC filter foam if I find it necessary.
So I kind of got carried away with making my case dust resistant, and added more dust filters to the case. See below:
This one keeps any extraneous dust from entering the 5.25″ bays
And that’s all for now. I might go crazy and buy some more filter material and make more filters for the PSU intake and bottom fan.
So a few weeks ago, I noticed quite a bit of dust buildup on the outside of my case side panel, right on the mesh around where the fan is. I opened up the case and found more dust on the inside than I would have liked to see. Then again, my system was running 24/7 for about 5 months; however I expected the fan filters to keep the dust out. Not the case here. After doing some research into the cause of the dust leaking in, it comes down to the negative pressure setup of the fans in the case causing dust to come in around the fan filters, wherever there is open, unfiltered mesh. I searched around for a solution, which came down to foam filter media which I originally found on ModDIY, however after looking into that site, I found out they are in Hong Kong and shipping would take 2 weeks by Registered Air Mail. So I searched some more, and came across a post on Overclock.net where a guy was asking where to find some thin foam filters, and turns out Lowe’s carries some.
Did some searching by walking down to the A/C filters aisle, and took a gander at some of the adjustable electrostatic filters made by Filtrete, but they were too thick, and I didnt exactly like the word “electrostatic” when thinking about where this filter was going to be.
So I downloaded the Lowe’s iPhone app and searched “foam filter” and it took me over to the window air conditioner section.
I wound up finding this 4.76mm filter media, for $1.58
I also picked up 2 cans of “dust remover” aka canned air, to spray out all the dust that was built up inside the case, and clean out my Corsair H80i radiator, which was already filled with dust.
To prevent more dust buildup on my radiator fins, I bought a Rosewill 120mm fan filter off Newegg, which should arrive sometime this week.
And so here is how I wound up modding the case side panel, mostly in pictures.
I first laid out the entire piece of filter media over the side panel (interior side up), then marked where the mesh was, then cut it down to size and marked where the fan mount holes are.
I then applied 1/2 inch strips of Scotch 3M Extreme Mounting Tape (rated for 20lbs) around the outline of the mesh.
Then I installed the fan, along with the NZXT fan filter that came with the case, and removed the backing on the adhesive to hold the foam down to prevent dust leakage.
And viola! Almost looks factory installed, and no change to the outside of the panel, except you cant see the fan. However, the only thing I care about is good airflow, minimal dust, and being able to see through the window.